10-13 Tundra OEM Camera Kit, Gentex Compass Mirror

Plug & Play incl. Gentex 335 Mirror

SKU: CS-10TUN-335


* Required Fields


Email to a Friend



This is an OE Fit Tundra backup camera kit that is plug and play with your factory wiring both front and back!  Don't spend $1800 on a camera kit from Toyota when you can have an OEM kit for a fraction the price! This kit utilizes our ultra clear super CMOS camera in a factory Tundra OEM handle, aftermarket handle, or camera module only (options). We bundle it with a factory rear harness and Gentex 335 auto-dimming video mirror with compass - best part is that it is plug and play into your existing wiring, making the installation time less than 30 minutes!  Finally see what is behind your vehicle while keeping your truck OEM!


Kit includes:

  • Factory Toyota tailgate camera handle, aftermarket handle, or no handle as camera module only (optional)
  • Camera Source Super CMOS night vision camera  - Latest camera technology for the ultimate in color, contrast, and clarity!
  • Gentex 335S auto-dimming video mirror with 3.3" RCD screen and Compass
  • OEM front harness - plug and play
  • Windshield wire cover (black cover that goes over the mirror wire as trim)
  • OEM rear harness - plug right into your factory wiring harness
  • Zip ties

Camera Specifications:

  • Super CMOS chip - outstanding color, contrast, and clarity!
  • 170 degree view
  • 600 TV lines of resolution
  • .2 lux minimum illumination - Outstanding night vision!

This kit allows you to see what is directly behind the truck - it will even see the rear bumper and hitch! Save $$$hundreds$$$ over a factory kit and get a better quality camera!


This camera comes with a 3 year limited warranty and is guaranteed to fit like it came from the factory or your money back.  5 year factory warranty on the mirror!

Additional Information

Additional Information

SKU CS-10TUN-335
Video System NTSC
Vehicle Interface Includes Rearview Mirror
Waterproof/Dustproof Level IP 67
Night Vision < .2 Lux
Power Supply 12 Volts
Wiring Type Factory Plug&Play
System Manufacturer EVI Systems
Monitor Size 3.3"
Camera Resolution 600 TVL
Parking Guidelines Selectable on/off
Camera Orientation Rear Facing
Fit Type Factory OE Fit Replacement
Connection Rearview Mirror
Sensor Type Super CMOS
Viewing Angle 170 Degrees
Camera Input Ports 1
Warranty 3 Year Limited
Mirror Options Auto Dim, Video, Compass
Mirror Mount Wedge Style

2010-2013 Tundra - Select your desired handle configuration from the box above when ordering.


NOTE: Some 2012 and 2013 trucks are not prewired even though the chassis harness is in place. You need to test each of the pins at the back for continuity in the front overhead console. This can be accomplished by using an ohm meter with a long extension wire and alligator clips. Clip one end of the wire to a pin at the back and carefully poke the opposite end of your tester into each of the overhead console wires to test for continuity. In the event that your Tundra camera wiring does not run all the way through you will need to order the Tundra full harness conversion kit CSH-TUN-335.

Installation Information

If you purchase just the camera module you will install our camera module into your camera-ready handle using the included bolts, route the harness through the bottom of tailgate and plug in on the frame rail.  This will only bolt into a factory or aftermarket handle with the OEM camera opening.  You can not drill a hole and make this system work.


If you purchase in a handle simply replace your existing tailgate handle with this handle containing the integrated backup camera. Two 10mm bolts hold your handle in place, swap the lock, fish the camera wire through the tailgate, plug in to your chassis, and reassemble. The entire camera installation process can take less than 20 minutes. 


Replace your factory mirror with the included Gentex mirror by removing the upper center console, remove the old mirror, swap with the new mirror, plug into the existing harness, and reassemble! - another 15-20 minutes.