Back-Up Camera for 2014-2018 Toyota Tacoma Factory Radios - Opt. Pop and Lock

Plug & Play with Factory Radio!

SKU: CS-14TAC

$124.00

* Required Fields

$124.00

Email to a Friend

Description

Details

This new Toyota Tacoma backup camera kit comes with your choice of either a camera module only, or premounted in a PL5500 or PL5400 Pop & Lock locking tailgate handle! In addition, it's completely plug and play with your factory radio. NOTE: some Tacomas are not prewired so please see compatibility tab for more information.

 

Now you can add a backup camera to your Tacoma quickly and easily without any cutting or splicing of wires. This Tacoma camera kit is completely plug and play at the back of the vehicle and uses the preexisting wiring to your factory Display Audio or Entune navigation radio (on factory pre-wired vehicles only). See the compatibility tab for details on vehicle fitment. If you need a Tacoma backup camera kit that will interface an aftermarket radio or OEM mirror see our other items as we have a kit that is sure to fit your needs.

 

The Pop and Lock tailgate handle offers additional security while keeping the OEM look of your Tacoma and is simple to install. You can choose from the PL5500, which comes with its own set of keys or choose the PL5400 which uses your existing key to program the lock tumbler so no additional keys are necessary.  Handles only compatible up to 2015 trucks. If you order just the camera module without the handle, the camera will mount in your existing handle using the factory screws. Included in this kit:

  • OEM grade 6 volt night vision backup camera with optional parking guidelines
  • (optional) PL5500 or PL5400 Pop and Lock locking tailgate handle (choose your Selection above). The camera will be premounted in the handle if ordered in this configuration. **Compatible only on trucks up to 2015.
  • Tacoma factory camera integration rear harness, or optional full length harness and radio interface connector for non-prewired trucks
  • Zip ties
  • Installation instructions

Rearview camera specifications:

  • Super CMOS sensor, high quality color, contrast, clarity and only available from Camera Source
  • 600 TV lines of resolution! The clearest color and clarity you will find.
  • 170 degree view
  • Waterproof/dustproof casing
  • Our Super CMOS backup cameras carry a 3 year limited warranty!
Additional Information

Additional Information

SKU CS-14TAC
Video System NTSC
Waterproof/Dustproof Level IP 67
Night Vision < .2 Lux
Power Supply 6 Volts
Wiring Type Factory Plug&Play
System Manufacturer EVI Systems
Camera Resolution 600 TVL
Parking Guidelines Selectable on/off
Camera Orientation Rear Facing
Fit Type Factory OE Fit Replacement
Connection Factory Connector
Sensor Type Super CMOS
Viewing Angle 170 Degrees
Warranty 3 Year Limited
Compatibility

2014+ Toyota Tacoma with factory touch screen radio/navigation (Display Audio or Entune) trucks. Please ensure your truck is prewired by checking the connector at the passenger side frame rail just in front of the rear bumper. If you have 4 wires in the frame side of this connector then you are prewired. If there is only one wire in this connector that heads toward the cab then you are not prewired and you need to Select the full harness configuration from the drop down above. This full harness config will come with the radio interface harness and a 28' chassis harness that will go from the camera to the radio.

 

NOTE: the 4 wires must run to the cab, not referring to the 4 wires that go into the tailgate.

Pop and Lock handles are compatible up to 2015 trucks.  

Installation Information

If you are pre-wired this kit simply plugs in at the frame rail using the tailgate disconnect factory plug. The total install will take 10-15 minutes! Watch the video below.

 

If you are not pre-wired you will run a new harness to the cab, come through an existing grommet in the floor board, then connect the camera harness to the radio using the included radio interface harness. This harness simply plugs right in to the radio without any cutting or splicing and this harness will also supply power and ground to the camera, which makes things really simple. You will also need to install the included reverse trigger wire into pin 2 of the factory radio bundle to trigger the radio into camera mode when you go to reverse. The total installation time is about 90 minutes or 120 minutes for DIY.  Watch the second video to learn how to remove the radio from your 2014+ Tacoma should you have to route this full harness.

 

 

Radio removal video: